6×16 Concrete Slab (6 inches): Yards, Feet & Bags
This 6 ft x 16 ft concrete slab, 6 inches thick, is perfect for a shed base or an AC pad. Consider access for delivery and whether to use bags or ready-mix.
Choose Your Calculator
Slab Calculator
Enter any custom length, width, and thickness to get cubic yards and bag counts.
Open Slab CalculatorBag Calculator
Choose 40/60/80 lb bag sizes and estimate counts for your exact volume.
Open Bag CalculatorWant other sizes? Browse all slab size pages
Quick Answer
Tip: Always confirm the yield printed on your bag label. Bag yield guide
Project Notes (Unique)
Check yield on the label and round to 0.25 yd³ for your order to ensure you have enough material.
Ensure your base is well-prepared and forms are sturdy to prevent issues with thickened edges.
Achieve a smooth finish and allow the concrete to cure properly in a shaded area, keeping it moist as needed.
6×16 Slab Thickness Check
A 6-inch slab gives this shed base extra stiffness and tolerance if soil conditions are imperfect or loads may grow over time.
Current spec
This page estimates a 6×16 slab poured at 6 inches.
Load check
Best fit depends on whether this is mainly pedestrian use, storage, or heavier wheel traffic.
Upgrade trigger
If you expect heavier loads later, compare this design against the alternate thickness before ordering.
Subgrade and Form Prep for 6×16
Most slab problems start below the concrete. Keep the base level, compacted, and consistent before you pour.
- Strip loose topsoil and organic material until you reach firm subgrade.
- Compact the base in lifts so the 6×16 slab does not settle unevenly.
- Check form height and diagonal measurements before concrete arrives.
- Plan reinforcement, joints, and edge support based on the intended shed base use.
Worked Example for 6×16 at 6 Inches
Step-by-step calculation for this exact slab:
- Convert thickness to feet: 6 ÷ 12 = 0.5000 ft
- Compute area: 6 × 16 = 96 sq ft
- Volume in cubic feet: 96 × 0.5000 = 48.00 ft³
- Convert to cubic yards: 48.00 ÷ 27 = 1.778 yd³
- Add 10% waste buffer: 1.778 × 1.10 = 1.956 yd³
Bag Mix or Ready-Mix for a 6-inch shed base?
This slab needs about 1.78 yd³ of concrete, or 80 80 lb bags before waste. With a waste cushion, plan around 1.96 yd³.
For this volume, ready-mix is usually the safer plan. Round up, confirm delivery minimums, and make sure your crew can place and finish the slab without delays.
Adjust dimensions in the slab calculator or compare bag counts here.
Bag Counts by Waste Buffer for 6×16
Pick a buffer based on site conditions: smooth forms and good subgrade can run leaner; uneven excavation or hard-to-reach pours need more cushion.
| Buffer | Yards (yd³) | 80 lb bags | 60 lb bags | 40 lb bags |
|---|---|---|---|---|
| +5% tight pour | 1.87 | 85 | 113 | 169 |
| +10% typical | 1.96 | 89 | 118 | 177 |
| +15% rough subgrade | 2.04 | 92 | 123 | 184 |
Cure Timeline for a 6x16 Concrete Slab
Protect the slab after finishing, keep the surface from drying too fast, and avoid heavy service until the concrete has had time to gain strength.
First 24 hours
Protect edges, prevent washout, and avoid unnecessary traffic while the slab sets.
Days 2-7
Maintain curing conditions and monitor joints, surface drying, and weather exposure.
Up to 28 days
Concrete keeps gaining strength, so wait for the right service window before heavy use.
How to Estimate This Slab in 3 Steps
Measure
Length 6 ft, width 16 ft, thickness 6 in.
Compute Volume
Area: 96 sq ft → volume: 48.0 ft³ → 1.78 yd³.
Add Waste
Add a small buffer for spillage and uneven subgrade, then round up when ordering.
Planning Notes
Common uses: shed base, ac pad, small patio section.
For more context and conversions, see the Concrete Calculator hub.
Frequently Asked Questions
What should I consider when deciding between bags and ready-mix?
Consider your project size and delivery access; ready-mix is convenient for larger areas, while bags may be easier for small projects.
How much extra material should I order for waste?
It's wise to factor in a little extra to cover spills or miscalculations, ensuring you have enough for the entire slab.
What is the best way to prepare the base for my slab?
Excavate the area to a stable, level surface and compact the soil to prevent settling after pouring.
How thick should my concrete slab be for a shed base?
A thickness of around inches is generally suitable for supporting a shed, providing durability against weight.
Related Slab Sizes
Ready to Calculate Your Project?
Get instant estimates for cubic yards, cubic feet, and bag counts. No signup required.